Wednesday, March 30, 2011

paper crane tutorial

today i found out about osh kosh's cranes for kids program. for every paper crane you bring in or take a picture of to mail in or post to their facebook page, they'll donate an article of clothing for tsunami survivors in japan. so, in the spirit of giving, for anyone who doesn't know how to make a paper crane, i've put together a tutorial for you. all you need is a square piece of paper and your hands. once you get it down, they take less than 5 minutes to make.

Photobucket

1) fold your paper diagonally so you have a triangle.
Photobucket

2) fold the triangle in half, then do it again.
Photobucket
Photobucket

3) open the last fold. now flatten the section that's on top so it forms a square.
Photobucket

4) flip the whole thing over and flatten that triangle section into a square as well.
Photobucket
Photobucket
Photobucket
Photobucket

5) there will be a crease running diagonally down the center of your square. fold one of the side corners in so the edge is flush w/ the crease. in this picture, the bottom of the paper is where all the corners are and you can see into the inside of the paper.
Photobucket

6) repeat w/ the opposite side. then flip the whole thing over and repeat on the back side.
Photobucket
Photobucket

7) it should look a little like an ice cream cone. fold the "ice cream" portion down over the "cone" portion. make sure to fold it BOTH ways, toward the front AND the back.
Photobucket

8) open the "ice cream" and "cone" flaps on one side so you have a square again.
Photobucket

9) pick up the TOP layer of paper only at the bottom of your square and make sure the paper bends where you made the crease from folding down the "ice cream."
Photobucket

10) flatten it out, making sure to carefully crease the edges so the paper doesn't rip.
Photobucket
Photobucket

11) flip over and repeat steps 9 & 10 on the other side.
Photobucket

12) you should have a very long, skinny diamond shape. fold the corner in so the edge is flush w/ the seam in the middle. there will be folds visible after you do this - make sure the folds are lined up like in the close up picture here.
Photobucket
Photobucket

13) repeat this on the other flap of the diamond.
Photobucket

14) flip over and repeat steps 12 & 13 on the 2nd side.
Photobucket

15) you should have an ever skinnier diamond shape now. lift one flap and fold it completely over itself. after doing this, you should have 3 flaps on one half and 1 flap on the other half.
Photobucket
Photobucket

16) flip over and fold the extra 3rd flap over itself so you again have 2 flaps on each half.
Photobucket
Photobucket

17) fold each of the narrow flaps up toward the thicker flaps.
Photobucket
Photobucket
Photobucket

18) again, fold one of the flaps completely over itself so you have 3 flaps on one half and 1 flap on the other half.
Photobucket
Photobucket

19) flip it over and repeat so you again have 2 flaps on each half.
Photobucket
Photobucket

20) the wider flaps are the wings - pull them GENTLY away from each other. the narrow flaps are the head and tail. it doesn't matter which is which. the side you choose for the head needs to have the tip bent down about 1/2 to 1 inch from the point (depending on how large a piece of paper you use). viola! you're done!
Photobucket
Photobucket
Photobucket

note: this is NOT the kind that you can pull the tail and get the wings to flap. i never learned how to make that type, but i've heard it's much more complicated.

2 comments:

  1. This comment has been removed by a blog administrator.

    ReplyDelete
  2. This comment has been removed by a blog administrator.

    ReplyDelete